我公司生産的NYP高粘度泵用作高粘度打膠泵是非常合适的泵從結構上看:自吸性能強，适用于輸送不含固體顆粒和纖維的粘稠液體，甚至是半固體狀态的液體，最高輸送💰粘度達到3*105厘泊。具有體積小、重量輕、脈動小、噪音低、運轉平穩、壽命長等優點。NYP high viscosity of the inner ring type pump is a kind of positive displacement rotor pump.This type of pump self-priming performance is strong, is suitable for conveying viscous liquid containing no solid particles and fibers, even half solid state of liquid, conveying viscosity up to 3 * 105 centipoise.With small volume, light weight, small ripple, low noise, smooth operation, long service life, etc.●高粘度泵工作原理：

　　高粘度泵是容積式内齧合齒輪泵，主動齒輪（外轉子）帶動被動齒輪（内轉子）旋轉時，不斷産生封閉的空間，在吸油區齒輪逐漸脫離齧合而液體不✍️斷地充滿齒間并被帶到出油區，齒輪在出油區進入齧❤️合時液體被排📧出。兩個旋轉齒輪的共同作用，形成一個穩定的體積排量，沒有脈動。由于泵是完全對稱的，泵可👈以反轉，液流方向也随之❗改變。但應注💘意，泵的轉向可能受到密封或泵💜内其它結構的限制，用戶有反🈲轉要求時應在訂貨時做🏒出說明。　　

●高粘度泵優點：

　　轉子泵的軸向位置可調，不需要拆泵。

　　泵采用模塊化設計，可根據不同的使用要求更換不同部件。可🐪選夾層結構，以方便對泵加熱或冷卻✌️，可以選擇是否帶安全閥，可以選擇不同的密封形式，詳見密封結構圖。泵的各個零件可以選用不同的材質以适應具體🍓使用要求。

　　不同的使用條件，泵的結構形式可能不同，具體應用請向廠⛱️家👅或本公司客戶代表咨詢。需要指出的是泵的轉速愈高，泵的磨損愈嚴重，液體中如含有磨料物質，泵的材料應💔選用耐磨材質，在此種工況下，泵的壓力和轉速都應降低，高溫條件下，則應增加泵的間隙，并采用耐熱材料 。

　　流動穩定：流量與齒輪轉速成正比，與壓力無關

　　流動平穩：沒有脈動和壓力波峰，不會産生管道顫👣動。

　　多功能性：僅僅通過調整轉子軸的位置，同一台泵既可以出😍來稀釋溶液又可以出來瀝青，糖漿，樹脂，聚合🤞物等高粘度液體。

　　可逆性：可以通過改變齒輪的旋轉方向使液體反向流動，兩種方向都能充分發揮泵的性能

　　自吸性：由泵産生高真空，允許在最大自吸高度實現快速自吸，取決于泵送液體的物理特性（溫度，蒸汽壓⭕力，粘度等）。

　　建議性：隻有兩個活動部件：主動輪和動輪，隻有一個軸㊙️封。

　　堅固的重載結構：低轉速。特大球軸承的外部軸承✔️座😍可以承受軸向和徑向負載。

　　磨損率低：由于主動輪和從動齒輪不成倍數關系。這就✉️意味🥵着磨損可以被均勻的分散在每個齒輪上。因㊙️為一個齒輪上的每一個齒輪接觸另一個齒輪上的✨每一個齒輪的次數一樣。

磨損調節系統：轉子邊緣的磨損可以通過調整轉子軸的位置來補償。這樣，即使在有相當大的磨損的情況下，也可以保證泵的穩定性。

　　維護簡單，維護率低：不用移動泵，管道或泵驅動裝置就可以進行檢查和調節。

　　互動性：标準組件的設計可實現不同材料和特性零部件之⭐間的替換。例如：有多種軸封系統可供選擇，還🧡可以安裝🏃‍♂️帶夾套的外殼和軸蓋來代替标準部件。

　　端口位置可改變：泵殼可在軸承箱上旋轉以從不同位置處吸排液體。

　　預熱：加熱夾套或是與外殼鑄成一體，或是安裝在端💋蓋上，或是安裝在填料壓蓋上。

　　旁路安全閥：旁路安全閥安裝在泵上并且容易調節，在☎️有👨‍❤️‍👨些🔴型🐕号的泵上采取雙重安全閥并帶加熱⭐夾套。●高粘度泵的工作壓力的選定

　　1, select the work pressure

　　高粘度泵額定的壓力是指泵連續工作時的最高許用⛷️壓力，而其工作壓力則決定于外部負載，安裝和調試的🐉壽命與其工作壓力直接相關。對于不頻繁工作的齒輪泵，其工作壓力可取為泵的額定壓力，考慮到産品質量不同，最🐪好将額定壓力降低20%～30%使用。對于經常工作于較高壓力下的齒輪泵，其工作壓力應比泵的額定壓力低1～2個壓力級。石油化工設備常常是24小時連續運轉，這時泵的工作壓力應該取得比額定壓力低👣得多，且工作轉速也應該低于額定轉速。如果高粘度齒輪泵的工作壓力調整過高，則會使齒輪泵在超負荷下運行。High viscosity pump rated pressure refers to the maximum allowable pump continuous work pressure, and its working pressure is determined by the external load, installation and commissioning of life is directly related with work pressure.For not frequent work gear pump, the working pressure is desirable for the rated pressure of the pump, taking the quality into consideration, it is best to used pressure rated lower 20% ~ 30%.For often work under high pressure gear pump, the working pressure shall be lower than the rated pressure of the pump 1 ~ 2 pressure level.Petrochemical equipment are often 24 hours of continuous operation, and at this time of the pump working pressure should be obtained was much lower than the rated pressure, and the work speed should be lower than the rated speed.If the high viscosity gear pump high pressure adjustment, will make the pump running under overload.

●NYP高粘度泵的安裝與試運轉

　　Installation and commissioning

　　高粘度泵的支座或法蘭與其驅動電機應采用共🧡同的安裝基礎，基礎、法蘭或支座均需具有足夠的剛度，以減小齒輪泵運轉時産生的振動和噪聲。電動機與齒輪泵須用彈性聯軸器連接，同軸度小于0.1毫米，傾斜角不得大于1度。安裝聯軸器時不得用錘敲打，以免傷害齒輪泵的齒輪等零件。若用帶輪、鍊輪等驅動時應設托架支承，以🐇防主✊動齒輪軸承受徑向力。緊固齒輪泵、電動機的地腳螺釘時，螺釘受力應均勻，連接可靠。用手轉動聯軸器時，應感覺到齒輪泵能夠輕松地轉動，沒有卡緊等異常現象出現，然後💁才可以配管。高粘度齒輪泵的吸油管道内徑應足夠大，并避免狹窄通道或急🤞劇拐彎、彎頭，去除不必要的閥門、附件，盡可能地降☀️低泵的安裝高度，縮短吸油管道的長度，以減少壓👅力損失。管接頭等元件🎯的密封要良好，以防止空氣侵入，從而控制氣穴與氣蝕的發生。在開始運轉前👄，往齒輪泵的殼體内灌滿待輸送的液體，便于安全動。若環境溫度😄低于冰點，應預先向泵内通入熱蒸汽，進行預👨‍❤️‍👨熱處💚理，然後才可啟動齒輪泵。齒輪泵的旋轉方向要與進、出油口相符。齒輪泵若是第一次運行，或長期閑置後再使用，最好在空載☎️或小⚽負荷情況下先跑合一小時左右。如果在跑合階段預先覺出異常溫升、洩漏、振動和噪聲時，應機檢查。高粘度泵的出口管路上還應當設置安全閥等保護裝置，這樣一旦泵的出口通道發生堵塞，就可以打開安全閥卸壓。對于需要正反轉的高粘度齒輪泵，其進出口管路上均需設置安全閥。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.