| 齒輪箱滑油泵用2CY3.3/0.33齒輪泵口徑G1 1/2-遠東泵業 |
| 發布時間：2015-1-28 15:35:43 點擊次數： |
用途:2CY齒輪泵主要用于各種機械設備中的潤滑系統中輸送潤滑油。Purpose: 2 cy gear pump is mainly used for all kinds of mechanical equipment of conveying lubricating oil lubrication system. 工作原理:本泵系容積式泵，主、被動齒輪與泵體、左右泵蓋組成進👨❤️👨油、出油☁️二個封閉空間，當齒輪轉動時，進油腔的容積，由于齧合齒不斷🈲脫開，而由小變大。形成真空，将液☂️體吸入，有齒谷🥵帶往油腔，而出油腔容積，由于齧合齒的不斷進入齧合而大變小，油液受壓縮而被排出，從而達到輸送油料的目的。Working principle: this pump is a positive displacement pump, the main around, passive gear and pump body, pump cover of the oil, the oil two closed space, when the gears, the oil cavity, the volume of meshing teeth off constantly, and changes from small to big.Form a vacuum, the liquid suction, toothed valley to the oil cavity, the volume of the oil cavity, due to the constant into the mesh of the meshing teeth and large to small, oil is displaced by compression, so as to achieve the aim of oil. 結構說明:本系列泵主要由：左、右泵蓋、泵體、主、被動齒輪軸、軸套、油🌂封等零件組成。Structure description: this series of pump is mainly composed of: left, right, pump cover, pump body, master, passive gear shaft, shaft sleeve, oil seal and other parts. 
工作注意事項:1、開機前應檢查泵軸轉動是否靈活，有無卡阻現象，進出口管道上的閥門是否開啟，泵的旋轉方向是🙇🏻否正确。2、長時間沒有使用的泵開機前應向泵腔中注入一定量的潤滑液，以減少泵在吸油過程中的幹摩擦，并可提高泵自吸性能。3、開機後如有不正常的噪音或過熱現象，應立即停車檢查。4、檢查泵軸端有無洩露現象，如：對填料密封應适當調緊壓🔞緊蓋、其他密封則應拆機檢查。5、若輸送熱油，在開車時應均勻預熱，預熱是利用被輸送的介質不斷通過泵體進行的。6、泵停機時，首先切斷電源，然後關閉進出口管道上的💰閥✔️門，避免造成泵倒轉。Work matters needing attention: 1, should check whether the pump shaft rotation is flexible, before starting the presence of jam phenomenon, import and export pipeline valve is open, the direction of rotation of the pump is correct.2, long time no use the pump to the pump before starting the cavity inject a certain amount of lubricant to reduce the pump in the dry friction in the process of oil absorption, and can improve the performance of self-priming pump.3, after the boot if there is any abnormal noise or overheating phenomenon, should immediately stop check.4, check whether there is any leakage on the pump shaft end phenomenon, such as: the packing should be properly tighten clamp cover and other sealing should teardown check.5, if conveying hot oil, while driving should be uniform preheating, preheating is to use the media constantly through the pump body to be delivered.6, when the pump stop, cut off power supply first, then close the import and export pipeline valve, avoid to cause back pump. 使用與安裝:1、機組應安裝在水平水泥基礎上，用地腳螺栓固定。2、右聯軸器應同軸，安裝完成後，轉動聯軸器确認運轉順暢無負💃🏻壓力現象後，方可進入運行。3、泵不适合輸送不潔油液，故在進口管端應設濾油器。4、泵無安全閥，建議在排油管路中，設安全閥，以确保🧑🏾🤝🧑🏼系統安全運行。5、泵的安裝高度，不超過允許吸上高度。6、泵的轉向規定：從泵端向電機看，旋轉方向為逆時針。Use and installation: 1, the unit should be installed in a horizontal cement, on the basis of land use fixed bolt.2, should right coupling coaxial, after the installation is complete, turn the coupling confirmed after running smoothly without negative pressure phenomenon, may run into.3, the pump is not suitable for conveying impurity oil, therefore, at the inlet pipe should be set oil filter.4 no relief valve, pump, it is suggested that in the discharge of oil pipeline, a safety valve, and to ensure the safe operation of the system.5, pump installation height, no more than allow on the suction height.6, pump steering regulation: look from the pump to the motor, for counterclockwise rotation direction. 工作原理:本泵系容積式泵，主、被動齒輪與泵體、左右泵蓋組成進油、出油二個封閉空間，當齒輪轉動時，進油腔💜的容積，由于齧合齒不斷脫開，而由小變大。形成真空，将液體吸入，有齒谷帶往油🌈腔，而出油腔容積，由于齧合齒的不斷進入齧合而大變小，油液受壓縮🔞而被排出，從而達到輸送油料的目的。Working principle: this pump is a positive displacement pump, the main around, passive gear and pump body, pump cover of the oil, the oil two closed space, when the gears, the oil cavity, the volume of meshing teeth off constantly, and changes from small to big.Form a vacuum, the liquid suction, toothed valley to the oil cavity, the volume of the oil cavity, due to the constant into the mesh of the meshing teeth and large to small, oil is displaced by compression, so as to achieve the aim of oil. 型 号 | 口徑 英寸 | 流量 | 壓力 MPa | 吸上高度（M） | 容積效率 % | 轉速r/min | 電動機 | m/h | L/min | 功率KW | 型号 | 2CY-1.08/2.5 | G" | 1.08 | 18 | 2.5 | 3 | 85 | 1420 | 1.5 | Y90L-4 | 2CY-2.1/2.5 | G1" | 2.1 | 35 | 2.5 | 3 | 85 | 1420 | 3 | Y100L2-4 | 2CY-3/2.5 | G1" | 3 | 50 | 2.5 | 3 | 85 | 1420 | 4 | Y112M-4 | 2CY-4.2/2.5 | G1" | 4.2 | 70 | 2.5 | 3 | 85 | 1420 | 5.5 | Y132S-4 | 2CY-7.5/2.5 | G1" | 7.5 | 125 | 2.5 | 3 | 85 | 1420 | 7.5 | Y132M-4 |
|
